by A. Guillermo Bracamonte

Received: 28 July 2023;  Published: 15 November 2023;  doi: 10.21926/rpm.2304034

This mini-review discussed the best-known chemical and synthetic methodologies used in the last years to modify carbon allotropes, with an interest in nanotechnology. In this perspective, chemistry with optoelectronics applications and recent trends within bio-applications focusing mainly on graphene and its derivatives were considered. So, the mini-review intended to focus on methodologies to add functional groups with varied reactivities, polymer chemistry, and nanoscale control. These methodologies provide insig [...]

by Jeffrey B. Allen  , Guillermo A. Riveros  , Ivan P. Beckman  and Elton L. Freeman

Received: 22 August 2023;  Published: 25 October 2023;  doi: 10.21926/rpm.2304033

In this work, we apply a multiphysics approach to fused deposition modeling to simulate extrusion and solidification. Restricting the work to a single line scan, we focus on the application of polylactic acid. In addition to heat, momentum and mass transfer, the solid/liquid/vapor interface is simulated using a front-tracking, level-set method. The results focus on the evolving temperature, viscosity, and volume fraction and are cast within a set of parametric studies, to include the printing and extrusion speed, a [...]

by Sujeet Kumar Thakur  and Sambasivan Venkat Eswaran

Received: 17 June 2023;  Published: 01 September 2023;  doi: 10.21926/rpm.2303032

The Inert soil obtained from the Ghazipur Municipal Solid Waste landfill located in East Delhi, India has been used as the starting material for the work described in this paper. This mountain-like monster is often in the news for its bad smell, pollution of the groundwater in the area from its leachates, and the occasional fires in it endangering the lives of the people living nearby. Landfills produce many greenhouse gases (CO2, CH4, CO, HCHO, H2S, and NH3) which are poisonous and cause environmental pollution in [...]

by Zhong Hu  and Haiping Hong

Received: 21 March 2023;  Published: 16 August 2023;  doi: 10.21926/rpm.2303031

The chemically functionalized carbon nanotubes (f-CNTs) and hydrogen bonding modified polymer composites (CPCs) exhibit unique chemical, mechanical, electrical, and thermal properties and are emerging as promising materials to achieve extraordinarily high electrical and thermal conductivity, lightweight and anticorrosion, superior strength and stiffness for potential applications in the aerospace and automotive industries, energy conversion, and optical and electronic devices, therefore, attracting considerable res [...]

by A. Guillermo Bracamonte

Received: 26 May 2023;  Published: 04 August 2023;  doi: 10.21926/rpm.2303030

This brief letter presents this Special Issue nominated as “Hybrid Graphene-based Materials: Synthesis, Characterization, Properties, and Applications”. This intends to show and discuss the main properties of Graphene and its derivatives; and how it could be synthesized, modified and tuned for Optics, Electro-Optics, Electronics, and Quantum characteristics. In this context, the synthesis and chemical modifications were highlighted for the design of Hybrid composites, platforms. In this context, it was afforded to [...]

by Fathi M. Layas  , Vail Karakale  and Ramadan E. Suleiman

Received: 28 April 2023;  Published: 27 July 2023;  doi: 10.21926/rpm.2303029

In recent years, regional wars and terror activities have caused blast-loading effects on reinforced concrete buildings, resulting in catastrophic human and material damage. When a building is exposed to a blast load, a very high air pressure affects the building within a very short duration. To decide on the reconstruction or retrofit of a building exposed to blast loading, the behavior of the building under blast loading should be investigated. In this paper a case study of a RC building exposed to blast loading [...]

by Alireza Modir  , Arnaud Casterman  and Ibrahim Tansel

Received: 10 January 2023;  Published: 26 July 2023;  doi: 10.21926/rpm.2303028

The process of metal additive manufacturing (AM) involves creating strong, complex components by using fine metal powders. Extensive use of AM methods is expected in near future for the production of small and medium-sized batches of end-use products and tools. The ability to detect loads and defects would enable AM components to be used in critical applications and improve their value. In this study, the Surface Response to Excitation (SuRE) method was used to investigate wave propagation characteristics and load [...]

by Rayara Silva dos Santos  , Pedro Henrique Poubel Mendonça da Silveira  , Beatriz Cruz Bastos  , Marceli do Nascimento da Conceição  , Roberto Carlos da Conceição Ribeiro  and Daniele Cruz Bastos

Received: 22 May 2023;  Published: 18 July 2023;  doi: 10.21926/rpm.2303027

This article presents the development and characterization of environmentally friendly composites comprising polypropylene (PP) reinforced with Bahia Beige (BB) marble waste. The composites were prepared using different PP/BB weight ratios and analyzed for their chemical, physical, mechanical, microstructural, and thermal properties. X-ray fluorescence (XRF) analysis revealed the composition of BB, which exhibited a significant concentration of CaO, indicating the presence of calcite and other oxides. X-ray diffrac [...]

by Vardan Apinyan

Received: 30 March 2023;  Published: 24 June 2023;  doi: 10.21926/rpm.2302026

This paper considers a finite-sized two-leg ladder of spin-1/2 particles with local inter-chain Ising interaction. We include the effects of an external magnetic field by incorporating a Zeeman-type coupling between the magnetic field and the spins localized on the lattice sites. To analyze the system, we utilize the transfer-matrix formalism to calculate the partition function. We compute the magnetization for different configurations by varying the system's parameters. We observe the presence 3of spontaneous magn [...]

by Subodh K. Mital  , Steven M. Arnold  , Brett A. Bednarcyk  and Evan J. Pineda

Received: 23 January 2023;  Published: 20 June 2023;  doi: 10.21926/rpm.2302025

The behavior and response of ceramic matrix composites (CMCs), in particular silicon carbide fiber reinforced silicon carbide matrix (SiC/SiC), is affected by many factors such as variation of fiber volume fraction, residual stresses resulting from processing of the composites at high temperature, random microstructures, and the presence of matrix flaws (e.g., voids, pores, cracks etc.) as well as general material nonlinearity and heterogeneity that occurs randomly in a composite. Residual stresses arising from the [...]

by Sumita Jain  , Noufa Khan  , Yena Park  , Densen Cao  and Daniel CN Chan

Received: 02 May 2022;  Published: 15 June 2023;  doi: 10.21926/rpm.2302024

Zinc pyrithione (ZPT) is used to prevent microbial degradation and deterioration of manufacturing starting materials such as plastics, polymers, and latexes. The main objective of this study was to evaluate the anti-bacterial properties of ZPT. Currently, there is insufficient data on the effect of ZPT on viability of commonly encountered bacterial pathogens. We tested the efficacy of ZPT manufactured in the form of film rolls as an anti-bacterial protective layer by using the ASTM–recommended protocol on gro [...]

by Hazal Turasan  , Tahrima B. Rouf  , Tuncay Yilmaz  and Jozef L. Kokini

Received: 26 October 2022;  Published: 12 June 2023;  doi: 10.21926/rpm.2302023

Nanomaterials are now used in almost every field of science; as conductors and electrodes in electronics, as nanodelivery systems in health screenings and drug delivery, as nanofibrils in filtering and textile industry, as nanoparticles in biosensor fabrication for toxin and pathogen detection, and in packaging materials in the food industry. Synthetic materials and plastics accumulate in the environment causing increasing health concerns for their use in food and pharmaceutical products. Therefore, researchers now [...]

by Eugene Adamovich  , Eugenia Buryanskaya  , Anthon Elfimov  , Irina Maklakova  , Oleg Gradov  , Margaret Gradova  and Theodor Orehov

Received: 27 December 2022;  Published: 29 May 2023;  doi: 10.21926/rpm.2302022

In this paper, starting with an introductory review of the applications of liquid crystals and polymer-dispersed liquid crystal systems in (bio)sensors and microfluidics, the possibilities of visualizing self-organization products of liquid crystalline media or field-induced instabilities of liquid crystalline systems are considered. In particular illustrated cases, it is proposed to use FemtoScan software-containing metrological complexes to visualize instabilities in liquid crystalline systems and products of sel [...]

by Abolfath Askarian Khoob  , Mohammad Javad Ramezani  and Seyed Sina Mousavi

Received: 16 June 2022;  Published: 12 May 2023;  doi: 10.21926/rpm.2302021

This study intends to determine the behavior of glass laminate aluminum-reinforced epoxy (GLARE) and glass fiber-reinforced polymer (GFRP) composites under a low-velocity impact test. Experimental tests and numerical simulations are considered for this investigation. All samples are made by the hand lay-up method. Moreover, specimens are produced with a 7075-T6 aluminium sheet with a 0.5 mm thickness, resin 3001, and E-glass fiber. The drop weight test performs the low-velocity impact at 6.7 J and 10 J impact energ [...]

by Aadharshini Ganesh  , Nisha Gupta  , Prosenjit Saha  and Pallab Bhattacharya

Received: 31 January 2023;  Published: 08 May 2023;  doi: 10.21926/rpm.2302020

Energy storage devices (ESD) including batteries, and supercapacitors are becoming progressively imperative in the transition to a renewable energy future, as they enable the integration of intermittent renewable sources into the grid and provide backup power during outages. There are already reviews available on various energy storage materials and systems. However, the challenges in the choice of suitable materials and fabrication technology are yet to establish for the commercialization of affordable and efficie [...]

by C. Shawn Sun  , Nahid Farzana  , Dinesha Kuruppuarachchi  , Mohammadamin Azimi  and Huayuan Zhong

Received: 10 September 2022;  Published: 04 May 2023;  doi: 10.21926/rpm.2302019

Infrastructure degradation attributable to concrete deterioration and corrosion of reinforcing steel has been a long-standing challenge to the owners and engineers. This problem becomes more evident when concrete structures are subject to aggressively corrosive environments. The use of advanced materials such as ultra-high performance concrete (UHPC) and carbon fiber reinforced polymer (CFRP) bars has a strong potential to overcome this challenge and help build new infrastructure that is durable and sustainable. Ho [...]

by Krzysztof Wierzcholski  and Jacek Gospodarczyk

Received: 26 April 2023;  Published: 27 April 2023;  doi: 10.21926/rpm.2302018

CorrectionCorrection: Non Solved Contemporary Scientific Problems of Non-Conventional Bio-Surfaces Lubrication. Recent Progress in Materials 2023; 5(1): 013Krzysztof Wierzcholski *, Jacek GospodarczykWSG Bydgoszcz University Garbary 2, Bydgoszcz, Poland; E-Mails: Krzysztof.wierzcholski@wp.pl; jacek.gospodarczyk@byd.pl* Correspondence: Krzysztof Wierzcholski; E-Mail: Krzysztof.wierzcholski@wp.plAcademic Editor: Hossein HosseinkhaniSpecial Issue: Non-Conventional Hydrodynamic Lubrication for Biological and Mechanic [...]

by Dipti Nikam  and Abbas S. Milani

Received: 05 May 2022;  Published: 24 April 2023;  doi: 10.21926/rpm.2302017

This study evaluates the influence of different loading angles and the area of loading on the ensuing stress distribution and the physical response of a natural central incisor tooth, using a 3D finite element analysis. The CAD model of the incisor tooth assembly (including enamel, dentin, periodontal ligament, pulp, gingiva and jaw bone) was subject to an external (chewing) load of 100 N, over four different areas and at four different angles along the vertical. It was observed that the tooth experiences high von- [...]

by Amir Mahboob  , Omid Hassanshahi  , Abdulqaiyoum Hakimi  and Mohammad Safi

Received: 02 March 2023;  Published: 19 April 2023;  doi: 10.21926/rpm.2302016

The largest proportion of the material used in multistory buildings, and thus its carbon impact, is attributed to their slabs being the main contributor of weight. Because of their high strength and concrete self-weight reduction, composite beams with hollow-core slabs were created for their technical and economic benefits, making this system inexpensive and with a reduced environmental impact, thereby lowering carbon emissions. Geometrically, the hollow slab has a sequence of T and L form pieces on both sides. Hol [...]

by Mohammed Naveed

Received: 22 December 2022;  Published: 12 April 2023;  doi: 10.21926/rpm.2302015

Composite materials with aluminum as matrix material have a wider amplitude of large-scale applications in engineering. Some salient features of aluminum matrix composites are, low density, low thermal coefficient of performance and low weight and high strength. Among the various series of aluminum alloy, Al6061 have been widely used by researchers due to its outstanding properties particularly as they are heat treatable. Aluminum 6061 alloys have been reinforced with various particulate reinforcements such as sili [...]

by Kikuko Hayamizu  , Tomoyuki Haishi  , Yasuhiko Terada  , Kunimitsu Kataoka  and Junji Akimoto

Received: 24 January 2023;  Published: 03 April 2023;  doi: 10.21926/rpm.2302014

Pulsed field-gradient (PFG) NMR spectroscopy was applied to thin disk samples (0.5, 1 and 2 mm thick, 4 mm diameter) of LLZO-Ta (Li6La3Zr1.5Ta0.5O12) single crystal. We have measured the diffusion of 7Li in thin pellets (0.5 to 3 mm thick) of NASICON-type LAGP powder and found that the Li+ diffuses preferentially in the thicker direction. In this study, we placed 1 mm thick, 4 mm diameter disk-shaped single crystals vertically, i.e., parallel to the PFG direction. We found that 7Li ions diffuse similarly as in rod- [...]

by Krzysztof Wierzcholski  and Jacek Gospodarczyk

Received: 19 December 2022;  Published: 27 March 2023;  doi: 10.21926/rpm.2301013

This paper presents new non solved, scientific research directions and their applications in contemporary non-conventional lubrication problems of the bio-surfaces domain. Here are described new research scientific trends and research problem solutions of hydrodynamic lubrication for living tissue, human skin and human cartilage joints surfaces. At first in introduction is described the state of the art, a new purpose of anticipate research and the bio-tribology connections with other scientific domains are documen [...]

by Suhail Hyder Vattathurvalappil  , Syed Fahad Hassan  and Mahmoodul Haq

Received: 24 January 2023;  Published: 16 March 2023;  doi: 10.21926/rpm.2301012

Thermoplastics polymers like Acrylonitrile Butadiene Styrene (ABS) are often reinforced with nano/micro reinforcements to enhance their mechanical, thermal and electrical properties. However, the viscoelastic nature of these polymers results in their strong dependence on the applied strain rate and temperature sensitivity, leading to their characterization complexity. Hence it is paramount to study the strain rate-dependent mechanics of neat ABS. In this study, the effect of strain rate and temperature on Young’s m [...]

by Recent Progress in Materials Editorial Office

Received: 28 February 2023;  Published: 28 February 2023;  doi: 10.21926/rpm.2301011

RetractionRetraction: Roy S. Performance of Grouted Coupler Embedded in Reinforced Concrete ABC Bridge Pier at Vehicle Impact. Recent Progress in Materials 2023; 5(1): 001Recent Progress in Materials Editorial OfficeLIDSEN Publishing Inc., 2000 Auburn Drive, One Chagrin Highlands, Suite 200, Beachwood, OH, USA; E-Mail: rpm@lidsen.com Recent Progress in Materials2023, volume 5, issue 1doi:10.21926/rpm.2301011Received: February 28, 2023Accepted: February 28, 2023Published: February 28, 2023

by Recent Progress in Materials Editorial Office

Received: 26 February 2023;  Published: 27 February 2023;  doi: 10.21926/rpm.2301010

InterviewAn Interview with Assoc. Prof. Carlo SantulliRecent Progress in Materials Editorial OfficeLIDSEN Publishing Inc., 2000 Auburn Drive, One Chagrin Highlands, Suite 200, Beachwood, OH, USA; E-Mail: rpm@lidsen.com Recent Progress in Materials2023, volume 5, issue 1doi:10.21926/rpm.2301010Received: February 26, 2023Accepted: February 26, 2023Published: February 27, 2023

by Leonid Dvorkin  , Vadim Zhitkovsky  and Ruslan Makarenko

Received: 12 January 2023;  Published: 24 February 2023;  doi: 10.21926/rpm.2301009

The article proposes a method that considers the parameters of heat and moisture treatment of concrete when designing its composition. Based on the analysis of experimental data, formulas are proposed that allow taking into account the type and characteristics of cement, the characteristics of aggregates, the effect of temperature and duration of steaming, and the water-cement ratio. Graphs and nomograms have been obtained, which makes it possible to simplify the calculation procedure according to the proposed meth [...]

by A. Guillermo Bracamonte

Received: 30 December 2022;  Published: 13 February 2023;  doi: 10.21926/rpm.2301008

In the present work we describe the most important quantum properties of graphene and derivatives recently published. We discuss how these properties were incorporated into varied hybrid materials such as substrates for specific tuning of matter to track varied quantum signals. Their potential applications were analyzed from nanomaterial and nanotechnology. In particular graphene, its derivatives and other carbon-based allotropes were chosen due to their special chemical structure and properties from the nanoscale [...]

by Ju dong Lee  , Jinho Kim  and Seungjoo Lee

Received: 29 September 2022;  Published: 16 January 2023;  doi: 10.21926/rpm.2301007

Most spent coffee grounds (SCGs), a byproduct of brewing coffee, are buried in landfill sites, and their decomposition produces significant greenhouse gases. As the recent warming of the Earth’s climate has made it imperative that industries reduce greenhouse gas emissions, the present study investigates the viability of recycling SCGs for use as a partial replacement of aggregates in concrete materials. Cement mortar samples with a fixed cement-to-water ratio and varying amounts of SCGs were fabricated and tested. [...]

by Udeme Udokpoh  and Chidozie Nnaji

Received: 02 September 2022;  Published: 12 January 2023;  doi: 10.21926/rpm.2301006

The several furniture-making phases, from cutting to processing to polishing, produce a significant volume of sawdust of differing grades. The extraction and disposal of such waste in developing countries with no established or sustainable methods is an increasing problem, frequently posing environmental challenges. Sawdust is one of the most underused wood waste portions, with mounds dispersed around the region, detracting from its visual appeal and causing other ecological concerns. This study investigated potent [...]

by Mariarosaria Angrisano  and Francesco Fabbrocino

Received: 02 August 2022;  Published: 11 January 2023;  doi: 10.21926/rpm.2301005

Nowadays, the challenge of climate change and “ecological transition” is substantially an “energy challenge” for every city, which is supposed to become as “energetically self-sufficient” as possible. The construction sector is one of the main contributors to the effects of climate change, starting from the production of materials to the use phase of buildings to their demolition. Recent innovations in sustainable/circular design are related to using “new materials." According to this perspective, nanomaterials are [...]

by António A. L. Ferreira  , Pedro Delgado  , Helena Parauta  , Charles V. Löwenström  and Joana O. Almeida

Received: 30 September 2022;  Published: 11 January 2023;  doi: 10.21926/rpm.2301004

In the context of inspection and maintenance actions for beach walkways in the North of Portugal, some samples of wood used in their construction were collected – the Pinus sylvestris wood, widely applied in the country. The sustainability of the beach walkways over natural coastal areas is very dependent on their material durability. One of the main problems of the timber used to build those structures is its behavior under wet-drying cycles. For that reason, this work aimed to simulate the effects of weathering o [...]

by Adefemi Adebisi Alade  and Ahmed Ibrahim

Received: 22 September 2022;  Published: 09 January 2023;  doi: 10.21926/rpm.2301003

Performance evaluations of wood and other lignocellulosic-based composites involve complex scenarios of several factors such as material heterogeneity and geometry that often leads to complicated, expensive, and time-consuming experimental procedures. Hence, the application of computational modeling and simulation is desirable to mitigate these biocomposites’ performance testing challenges. This review paper, therefore, presents an outlook on the finite element method (FEM) application in probing performance charac [...]

by Recent Progress in Materials Editorial Office

Received: 04 January 2023;  Published: 04 January 2023;  doi: 10.21926/rpm.2301002

The editors of Recent Progress in Materials would like to express their sincere gratitude to the following reviewers for assessing manuscripts in 2022. We greatly appreciate the contribution of expert reviewers, which is crucial to the journal's editorial process. We aim to recognize reviewer contributions through several mechanisms, of which the annual publication of reviewer names is one. Reviewers receive a voucher entitling them to a discount on their next LIDSEN publication and can download a certificate of re [...]

by Suman Roy

Received: 27 September 2022;  Published: 03 January 2023;  doi: 10.21926/rpm.2301001

Increased occurrence of dynamic loading on bridge piers caused by seismic, blast and vehicular impact incidences have been increasingly reported. Statistical data shows that while seismic and blast have received significant attention in the literature despite the frequency of occurrence of vehicular impact is remarkably higher. Unfortunately, pier damage caused by high velocity vehicle impact contemplates a little consideration. With the newer construction methods like accelerated bridge construction (ABC) and its [...]

by Chingrishon Kathing  and Geeta Saini

Received: 15 October 2022;  Published: 30 December 2022;  doi: 10.21926/rpm.2204028

Wastewater generated by the textile industry has been a major environmental concern for a long. Production of fiber involves various steps and uses a lot of chemicals, dyes, and water. Therefore, the effluent produced from the textile industry needs proper purification before discharging into the water body. The current review summarizes various physical and chemical methods like ion exchange, coagulation-flocculation, membrane separation, membrane distillation, oxidation, ozonation, etc., for wastewater treatment. [...]

by Ladislaus Alexander Bányai  and Mircea Bundaru

Received: 21 October 2022;  Published: 08 December 2022;  doi: 10.21926/rpm.2204027

We describe here the coherent formulation of electromagnetism in the non-relativistic quantum-mechanical many-body theory of interacting charged particles. We use the mathematical frame of the field theory and its quantization in the spirit of the quantum electrodynamics (QED). This is necessary because a manifold of misinterpretations emerged especially regarding the magnetic field and gauge invariance. The situation was determined by the historical development of quantum mechanics, starting from the Schrödinger e [...]

by Jeet Chand  , Shiva Jha  and Sameer Shrestha

Received: 29 August 2022;  Published: 25 November 2022;  doi: 10.21926/rpm.2204026

Water recycling is a potential tool for reducing the dependency on traditional water sources, which would eventually reduce the likelihood of volumetric restrictions and their impacts on the water sector. Therefore, exploration, development, and use of alternative water sources are required for sustainable development. Scientific studies on the efficient and economical use of nontraditional water sources developed using the recycling process have attracted the attention of agriculturists, planners, and engineers fo [...]

by Pratik Shukla  , Vincent Zhang  , Xiaojun Shen  , Victor M. Villapún  , Sophie Cox  and Phil Swanson

Received: 10 April 2022;  Published: 22 November 2022;  doi: 10.21926/rpm.2204025

This is a multi-disciplinary paper focused on the preliminary results of deploying laser shock treatment (LST) to ZrO2 ceramics. This work has significance in several industrial sectors for components that will benefit from strengthening. These components are, namely: dental implants; cutting and drawing tools; valves, bearings, pressure vessels, heat exchangers and high-performance scissors and knives, where modification of hard, brittle materials properties such as that of a ZrO2, can yield a performance boost. T [...]

by Rim Werheni Ammeri  , Wafa Hassen  , Ines Mehri  , Nesrine Khelifi  and Abdennaceur Hassen

Received: 29 July 2022;  Published: 18 November 2022;  doi: 10.21926/rpm.2204024

Bioaugmentation by Pseudomonas strains is widely used for the removal of pollutants in wastewater. In this study, we aimed to determine the removal of pentachlorophenol (PCP, 800 mg·L–1) in secondary wastewater by the bioaugmentation process. We determined the effects of using three surfactants, namely sodium dodecyl sulfate (SDS), cetyl-tri-methyl-ammonium bromide (CTAB), and Tween 80 for PCP removal. We determined the effect of the role of PCP surfactant for the biofilm and auxin production of the se [...]

by Oleksandr Beshta  , Gennadiy Pivnyak  , Oleksandr Beshta Jr  , Roman Borovik  , Cáceres Cabana Edgar  and Adam Smolinski

Received: 17 August 2022;  Published: 14 November 2022;  doi: 10.21926/rpm.2204023

In a lithium-ion battery, the crossing of its charging–discharging curves represents an unambiguous current capacity. The reproduction of a complete charging–discharging cycle defines the maximum possible charge for a current battery state. When obtaining of the curves experimentally, one should consider the duration of polarization or depolarization. It is reported that the battery capacity depends considerably on the value of the battery’s internal resistance as this value defines the location of the actual charg [...]

by Dafni Foti  , Costas Passialis  , Elias Voulgaridis  and Stergios Adamopoulos

Received: 23 August 2022;  Published: 28 October 2022;  doi: 10.21926/rpm.2204022

Cellulosic fibrous mats were impregnated with various water-repellent formulations based on reclaimed polystyrene (5, 10, 15, and 20%), alkyd resin (5%), gum rosin (5%), and paraffin wax (0.5%). The mats were tested for their bursting strength and resistance to bending. They were also subjected to the ring crush test and short-span compression test. By increasing the concentration of total solid ingredients (5, 10, 15, 20, and 25.5%), the retention and grammage of the mats were increased, and all strength propertie [...]

by Mohammad Yaghoub Abdollahzadeh Jamalabadi

Received: 09 July 2022;  Published: 19 October 2022;  doi: 10.21926/rpm.2204021

New lubrication events can be predicted using improved pathological non-Newtonian physiological fluids coupled to phospholipid-based bilayers in variable time-dependent magnetic fields under random non-steady conditions. In this study, we investigated nanofluid lubrication systems for synovial joints. The particles of PSPMA-g-HSNPs were used as nanoparticles. The hydrodynamic interaction between the knee bones separated by a nanofluid film was considered here for various nanofluid concentrations. The simulation ind [...]

by Navya Uppu  , Kelly McMahen  , Tasneem Khasru  and Mark A. DeCoster

Received: 02 August 2022;  Published: 17 October 2022;  doi: 10.21926/rpm.2204020

Green synthesis of nanomaterials endeavors to reduce the use of high energy methods with those that may include lower temperatures and pressures, use of natural products, and bottom-up self-assembly. Here we describe the generation of metal-organic biohybrids (MOBs) with nanoscale features synthesized at physiological (37°C) and room temperature (25°C). These MOBs utilized the naturally occurring amino acid dimer cystine as the biological component, and a series of metals, including copper, silver, and cobalt. The [...]

by William E Vargas  , Federico Muñoz-Rojas  , Esteban Avendaño  , Victoria Quirós-Cordero  and Marcela Hernández-Jiménez

Received: 30 July 2022;  Published: 12 October 2022;  doi: 10.21926/rpm.2204019

Spectrophotometry has been widely used to retrieve the dielectric function of a bulk iridium sample using an extended version of the Drude–Lorentz model. The parameters of the model are optimized using a spectral-projected-gradient-method-assisted acceptance-probability-controlled simulated annealing approach. Furthermore, optimized values of Drude parameters corresponding to the optical response of electrons and holes (scattering frequency of electrons, the ratio between scattering frequencies of holes and electro [...]

by Pierre Bernstein  , Yiteng Xing  and Jacques Noudem

Received: 07 July 2022;  Published: 15 September 2022;  doi: 10.21926/rpm.2203018

Stable levitation of systems consisting of a magnetic source and a superconductor is actively investigated due to the promising applications of this technology. While huge efforts have been made for modeling these setups with numerical simulations, analytical models, in spite of their use being limited to devices with a high degree of symmetry, can bring precious information on certain characteristics of levitating systems. Summarizing our previous work in the field, we present the mean-field model that we have pro [...]

by Mayra De Grazia  , Cassandra Trottier  , Sergio R.A. Dantas  , Yathiraj Nagaraju  , Rouzbeh Ziapour  , Hian F. Macedo  and Leandro F.M. Sanchez

Received: 11 July 2022;  Published: 07 September 2022;  doi: 10.21926/rpm.2203017

The ever-growing urgency to combat climate change has led the civil construction industry to develop and adopt sustainable construction materials and methods. The so-called recycled concrete aggregate (RCA) emerges as an alternative to decrease the carbon footprint of new concrete construction, the disposal of waste concrete, and the use of non-renewable natural resources such as cement and aggregates. RCA can be produced from crushing waste concrete; yet challenges remain when using RCA in concrete especially its [...]

by Recent Progress in Materials Editorial Office

Received: 29 August 2022;  Published: 30 August 2022;  doi: 10.21926/rpm.2203016

Interview An Interview with Prof. José Ignacio Álvarez GalindoRecent Progress in Materials Editorial OfficeLIDSEN Publishing Inc., 2000 Auburn Drive, One Chagrin Highlands, Suite 200, Beachwood, OH, USA; E-Mail: rpm@lidsen.comRecent Progress in Materials2022, volume 4, issue 3doi:10.21926/rpm.2203016Received: August 29, 2022Accepted: August 29, 2022Published: August 30, 2022

by Joana Sousa

Received: 10 March 2022;  Published: 24 August 2022;  doi: 10.21926/rpm.2203015

Exposure to indoor pollutants may exert a significant effect on children health as they spend most of their time in enclosed environments. This research compared the association of biological concentrations with indoor characteristics and building materials in places where children spend significant time indoors. It was compared the results of two autonomous research projects conducted in Porto primary schools and households. Both the projects included a walkthrough inspection and biological measurements in indoor [...]

by Chang Gu  , Hongmei Gu  , Meng Gong  and Janet Blackadar

Received: 21 April 2022;  Published: 05 August 2022;  doi: 10.21926/rpm.2203014

Mass timber products (MTPs) are being adopted in new building constructions and remodels in the last three decades, credited to their renewable and low carbon footprint characteristics. However, there are no mass timber manufacturers currently existing in Atlantic Canada. Extended distances of transporting MTPs to this region from other Canadian provinces may sacrifice the environmental benefits of using MTPs. This study was aimed to understand, via conducting a cradle-to-gate life cycle assessment (LCA), the envir [...]

by Mohammad Shanawar Khan  and Shohel Amin

Received: 15 May 2022;  Published: 04 August 2022;  doi: 10.21926/rpm.2203013

This study examines the chemical compositions of eggshell powder (ESP) and lime as the soil stabilisers and compared with the compositions of cement and fly-ash to understand the optimal distribution of chemical stabilisers maximising the bearing capacity and structural integrity of subgrade soil. The different proportions of eggshell powder (ESP) (2%, 4%, 6% and 8% of total soil mass) were mixed with a fixed proportion of lime (6% of total soil mass) to analyse the optimum proportion of eggshell maximising the soi [...]