by Taise M. Manhabosco  , Shaul Aloni  , Tevye R. Kuykendall  , Sara M. Manhabosco  , Ana Bárbara Batista  , Jaqueline S. Soares  , Ana Paula M. Barboza  , Alan. B. de Oliveira  , Ronaldo J. C. Batista  and Jeffrey J. Urban

Received: 06 September 2019;  Published: 29 October 2019;  doi: 10.21926/rpm.1904005

Tin telluride (SnTe) ultrathin films were deposited electrochemically on polycrystalline and monocrystalline gold substrates using the electrochemical atomic layer epitaxy (ECALE) method. The electrochemical behaviors of Sn and Te were studied systematically by means of cyclic voltammetry. Cyclic voltammetry curves for Sn displayed a broad peak in the region between -0.15 V and -0.35 V, which was related to the under-potential deposition (UPD), while the curves for Te displayed a peak at 0.3 V for Te UPD. X-ray pho [...]

by Ahalapitiya H Jayatissa  , Omer Ahmed  , Bodhi R Manu  and Adam M Schroeder

Received: 13 August 2020;  Published: 22 January 2021;  doi: 10.21926/rpm.2101003

The tribological properties of ZnO thin film coated on an aluminium work piece by RF magnetron sputtering were studied as a function of deposition power, substrate coating temperature, heat treatment and rotation speed. The variation in the coefficient of friction of ZnO films produced under various levels of coating parameters and conditions were experimentally determined using a pin-on-disk tribometer. The results showed that with change in deposition conditions and heat treatment, there are significant microstru [...]

by Fahriye Yagmur Bütün Buschalsky  and Carsten Mai

Received: 15 March 2021;  Published: 22 July 2021;  doi: 10.21926/rpm.2103029

A thermo-hydrolytic disintegration process qualifies as a promising option for recycling the waste MDF and preserving the fibrous morphology of the recovered lignocellulosic fibre material. This study aims to include a drainage process between the thermo-hydrolytic disintegration and the further utilization of the recovered fibres (RF) obtained using a screw press for removing the disintegration water (DW). In this context, the chemical properties of the RF (pH, nitrogen content, formaldehyde emissions) and the DW [...]

by Kianoush Hatami Dehnou  and Mohammad Jafar Hadianfard

Received: 14 December 2023;  Published: 03 May 2024;  doi: 10.21926/rpm.2402011

The use of silicone rubber as an implant is limited due to its weak properties. In this study, the impact of various reinforcements, such as TiO2 or SiO2 nanoparticles, carbon, or polypropylene fiber micro reinforcements, on the mechanical, thermal, and viscoelastic properties of silicone rubber composites with RTV-4125 matrix was investigated. The composites were evaluated through several tests, including tensile, compression, FTIR, TGA, DMTA, and water adsorption tests. It was found that the composites' tensi [...]

by Chris R. Lavers

Received: 29 December 2020;  Published: 14 May 2021;  doi: 10.21926/rpm.2102019

Advanced optical stealth techniques are of growing importance in the role of manned and unmanned aircraft or ship platforms. We consider here the concept of using passive reflective display elements rather than high power active light projection to achieve a low observable camouflaged ship platform. This paper presents practical consideration towards minimal radiated power user-driven requirements using adaptive liquid crystal electro-optical methods. Optical reflectivity for a multi-layer liquid crystal cell struc [...]

by Jeet Chand  , Shiva Jha  and Sameer Shrestha

Received: 29 August 2022;  Published: 25 November 2022;  doi: 10.21926/rpm.2204026

Water recycling is a potential tool for reducing the dependency on traditional water sources, which would eventually reduce the likelihood of volumetric restrictions and their impacts on the water sector. Therefore, exploration, development, and use of alternative water sources are required for sustainable development. Scientific studies on the efficient and economical use of nontraditional water sources developed using the recycling process have attracted the attention of agriculturists, planners, and engineers fo [...]

by Vardan Apinyan  and Mane Sahakyan

Received: 17 March 2020;  Published: 01 July 2020;  doi: 10.21926/rpm.2003016

The present report provides a phenomenological theory for monolayer graphene, in which two worlds, the quantum and the classical, meet and complete each other in the most natural manner. In the present report, electron mass-vortex representation is introduced, and the surface tension excitation states in the monolayer graphene are defined. The band-mass of the electrons at the Dirac’s point was calculated through the mathematical introduction of a mass-dispersion relation. As a consequence, the Dirac’s [...]

by H. Hakemi  , M. Khenkin  , R. Tamari  and D. Gal-Fuss

Received: 10 December 2019;  Published: 05 March 2020;  doi: 10.21926/rpm.2001006

In the present study, we report the experimental results related to the transient phenomenon, i.e., the time-dependent changes in the electro-optical properties of as-made polymer-dispersed liquid crystal (PDLC) films prepared by the UV-curing phase-separation method. This phenomenon occurs explicitly via polymer-induced phase separation when the matrix curing is not complete, some liquid crystal plasticized in the matrix, and some uncured pre-polymer components remain in the liquid crystal droplets. The outcome is [...]

by Sumita Jain  , Noufa Khan  , Yena Park  , Densen Cao  and Daniel CN Chan

Received: 02 May 2022;  Published: 15 June 2023;  doi: 10.21926/rpm.2302024

Zinc pyrithione (ZPT) is used to prevent microbial degradation and deterioration of manufacturing starting materials such as plastics, polymers, and latexes. The main objective of this study was to evaluate the anti-bacterial properties of ZPT. Currently, there is insufficient data on the effect of ZPT on viability of commonly encountered bacterial pathogens. We tested the efficacy of ZPT manufactured in the form of film rolls as an anti-bacterial protective layer by using the ASTM–recommended protocol on gro [...]

by Hossein Hosseinkhani

Received: 26 August 2024;  Published: 12 December 2024;  doi: 10.21926/rpm.2404027

Viral and non-viral vectors for nucleic acids (DNA/RNA) therapeutics are important in development of pharmaceutical industries. Although viral vectors have shown significant impact in transfection of DNA/RNA, but numerus studies have shown that non-viral vectors are also effective for the safe and targeted delivery of DNA/RNA to exact location in the body with high percentage of efficacy, safety, and low-immunogenicity. It is also important to protect the nucleic acids from degradation and large-scale production ca [...]

by Hassan-Ali Hakemi

Received: 11 October 2020;  Published: 08 December 2020;  doi: 10.21926/rpm.2004023

In this work, the experimental data on flexible PDLC films at the industrial scale and the effect of cure temperature (Tc) on the morphology and electro-optical properties of a UV-cured PDLC system via polymer-induced phase separation (PIPS) method were studied. Under constant UV radiation intebsity and thickness, the morphological parameters such as dimension, number density, and volume fraction of the phase-separated liquid crystal droplets as well as the optical transmissions and switching voltages as a function [...]

by Kátia R. A. Nunes  and Cláudio F. Mahler

Received: 11 August 2024;  Published: 24 December 2024;  doi: 10.21926/rpm.2404029

Construction and demolition waste (CDW) is a significant waste stream in Brazil. It represents 38.2% of the total CDW and MSW streams. The recycling of CDW in Brazil is estimated to be at least 7.2% by weight (collected CDW) or about 15% by volume (produced CDW). Therefore, only a tiny part of CDW is returned to construction activities. On the other hand, 48.9% of the total amount of the top fifty extracted minerals in the country is sand and gravel, which is used in the national construction industry. Considering [...]

by Mª Carmen Márquez

Received: 15 September 2023;  Published: 24 January 2024;  doi: 10.21926/rpm.2401002

Organics found in landfill leachate (humic acids, fulvic acids, and hydrophilic fraction) have a solid ability to absorb ultraviolet (UV) radiation, which negatively affects UV disinfection; leachate ultraviolet quenching substances (UVQS) can, therefore, have a significant impact on the cotreatment of landfill leachate and sewage in wastewater treatment plants. On the other hand, per- and polyfluoroalkyl substances (PFAS), which pose potential risks to the environment and human health, commonly exist in landfill l [...]

by Y. Ben-Aryeh

Received: 29 July 2019;  Published: 04 September 2019;  doi: 10.21926/rpm.1903003

In this article, microsphere super-resolution, which are beyond the Abbe classical limit, are described. The conversion of evanescent waves into propagating waves is analyzed by using the geometry of the microsphere. In microsphere experiments, a nanojet is produced near the focal plane, where its width is smaller than the Abbe limit and remains unchanged in the axial direction for certain wavelengths. The interference between the evanescent waves being converted into propagating waves and the nanojet leads to an i [...]

by Pithchai Pandian Sivakumar  , Elke Gruyaert  , Nele De Belie  and Stijn Matthys

Received: 09 March 2021;  Published: 02 June 2021;  doi: 10.21926/rpm.2102022

Depending on the availability of aggregate sources pertaining to their geographic locations, the concrete industry utilizes conventional aggregates such as marine sand, dredged gravel, or crushed rocks. This method requires high energy and high processing costs for washing and grinding. The objective of this work is to use Modified Ferro silicate slag (MFS), a by-product obtained from the copper industry, as an alternative to the conventional fine aggregates found in mortar. No additional processing such as washing [...]

by Christopher Wilson  , Anthenius Versluis  , Daranee Tantbirojn  and Martha Wells

Received: 10 February 2021;  Published: 28 May 2021;  doi: 10.21926/rpm.2102020

Prefabricated zirconia crowns (ZRCs) require a passive fit and more reduction than stainless steel crowns (SSC). To determine the mean and maximum reduction depths in the mesial-buccal and occlusal areas for three ZRC brands and one SSC in posterior primary typodont molars and to compare reduction depths to existing literature to determine the preparation’s proximity to pulpal tissue. Four primary maxillary and mandibular typodont teeth (J and S) were prepared according to the manufacturers’ guidelines for three ZR [...]

by Razieh Sadraei

Received: 25 April 2020;  Published: 01 July 2020;  doi: 10.21926/rpm.2003017

A literature survey shows that the valorization of urban and/or agricultural biowastes into chemicals has caught the attention of experts and is gradually becoming quite an important issue. This review presents the application of the Bio-Based Substances (BBS) isolated from the compost of bio-wastes from urban gardening and park trimming residues. The non-cost BBS has been well studied in the literature. BBS are biological macromolecules with a complex lignin-derived structure containing several functional groups, [...]

by Yi-Chia Liao  , Chun-Hway Hsueh  and Wen-Shin Lee

Received: 16 May 2020;  Published: 15 June 2020;  doi: 10.21926/rpm.2002014

Inspired by the application of metallic glass sheet as face material for improving the performance of golf clubs, the present work was aimed to explore the application of thin-film metallic glass (TFMG) coatings for enhancing the performance of strings. In order to achieve this aim, badminton strings were coated with TFMG coatings of different thicknesses. The compositions of these TFMG coatings were analyzed using an electron probe micro-analyzer. The amorphous structure of the film was verified using X-ray diffra [...]

by Trenton Cersoli  , Muneer Barnawi  , Kerry Johnson  , Edward Burden  , Frank Li  , Eric MacDonald  and Pedro Cortes

Received: 17 February 2022;  Published: 29 April 2022;  doi: 10.21926/rpm.2202009

Shape memory polymers (SMPs) are smart materials that can respond to certain thermal, chemical or electrical stimuli by inducing a structural conformation change into a temporary shape. In this work, a 3D printing process based on a Vat Photo-polymerization of a shape memory polymer (SMP) was investigated to produce customized smart and complex morphable antennas. The mechanical and material properties were examined through a tensile, flexural and rheological testing for different polymer mixture ratios. It was obs [...]

by Fabrice Debbasch

Received: 15 October 2019;  Published: 06 January 2020;  doi: 10.21926/rpm.2001002

A relativistic Wigner function for free Discrete Time Quantum Walks (DTQWs) on the square 2D space-time lattice is defined. The transport equation obeyed by the relativistic Wigner function is derived in terms of discrete derivatives and degenerates in the continuum limit into the transport equation obeyed by the Wigner function of 2D Dirac fermions. The first corrections to the continuous equation induced by the discreteness of the lattice are also determined and the similarities with non-quantum relativistic tran [...]

by Krzysztof Wierzcholski

Received: 08 October 2020;  Published: 02 June 2021;  doi: 10.21926/rpm.2102023

This paper aims to highlight the result of a new progression of mathematical estimation methods of stochastic bio-hydrodynamic lubrication parameters for arbitrary, curvilinear, non-rotational, co-operating, living biological surfaces coated with phospholipid bi-layers. Movable, non-rotational, co-operating surfaces occur in various biological friction nods like the collar bone, the blade bone, the jump joint, and the wrist joint. Specifically, the author presents a synthetic and comprehensive estimation of stochas [...]

by Mohammed Faruqi  , Zachary Scott Dean  , Francisco Aguiniga  and Breanna Bailey

Received: 15 November 2020;  Published: 15 January 2021;  doi: 10.21926/rpm.2101002

Prestressed concrete members have gained popularity as an efficient and effective way of designing a structural member with the best engineering and material properties. The method of prestressing a structural concrete member has the capability of controlling increased service loads with less depth over longer spans. However, deflections from over-loading or loading over time give a disadvantage to the common steel reinforced concrete members by the effect of corrosion as the structural concrete develop cracks. To [...]

by Mariusz KSIĄŻEK

Received: 24 March 2021;  Published: 15 June 2021;  doi: 10.21926/rpm.2102024

Metal parts of endoprosthesis have a detrimental effect on the bones that come into contact with them and on the entire body of the patient. Coating them with biocompatible layers (hydroxyapatite and bioglass) has not yet brought about permanent results. In this study, the author showed the possibility of using a binder containing sulfur waste for this purpose. The sulfur binder is used industrially in electrical engineering and construction applications. The chemical properties of elemental sulfur indicate that it [...]

by Dimitris Kouzoudis  , Georgios Samourgkanidis  and Christos I. Tapeinos

Received: 12 December 2020;  Published: 06 April 2021;  doi: 10.21926/rpm.2102010

In the current work, to identify the bending mode harmonics, 30 microns thin magnetoelastic ribbons made of metallic glass are embedded inside 6 mm thick PLA plastic cantilever beams made by 3-D printing. This is possible because the ribbons are of magnetoelastic nature and thus change their mechanical state inducing a corresponding change in their magnetic state. The ribbons are placed at four different depths, starting with zero depth at the beam’s external surface all the way inside to the beam’s mid-plane. This [...]

by CT Valliappan  , J Joyson Joe Asir  , V Subashri  , V Vaishnavi  and I Anand Sherwood

Received: 28 December 2020;  Published: 27 April 2021;  doi: 10.21926/rpm.2102014

Furcal perforation management in root canal retreatment is often challenging as the outcome of the perforation sealing depends on several parameters. The recent introduction of several bioactive cements and magnification systems has made the sealing of perforations easier and the outcome more predictable. This study highlights the clinical outcomes of furcal perforation management in root canal retreatment using biodentine.