by Raisa Barbosa  , Mohamad Issa  , Sidelmo Silva  and Adrian Ilinca

Received: 30 July 2021;  Published: 13 January 2022;  doi: 10.21926/jept.2201003

A substantial share of the electric energy is generated with synchronous generators that provide sustained alternating current (AC) voltage and frequency energy to regional and national power systems, which subsequently transport and distribute it to diverse users. In an attempt to reduce environmental effects, electric energy markets have recently become more open, resulting in more flexible distributed electric power systems. In such distributed systems, stability, quick and efficient delivery, and control of ele [...]

by Argyrios V. Karatrantos  , Md Sharif Khan  , Chuanyu Yan  , Reiner Dieden  , Koki Urita  , Tomonori Ohba  and Qiong Cai

Received: 24 May 2021;  Published: 27 September 2021;  doi: 10.21926/jept.2103043

The performance of metal-ion batteries at low temperatures and their fast charge/discharge rates are determined mainly by the electrolyte (ion) transport. Accurate transport properties must be evaluated for designing and/or optimization of lithium-ion and other metal-ion batteries. In this review, we report and discuss experimental and atomistic computational studies on ion transport, in particular, ion diffusion/dynamics, transference number, and ionic conductivity. Although a large number of studies focusing on l [...]

by Tran X Phuoc  and Mehrdad Massoudi

Received: 28 October 2021;  Published: 22 December 2021;  doi: 10.21926/jept.2104050

To store CO2 in geological reservoirs, expansion valves have been used to intentionally release supercritical CO2 from high-pressure containers at a source point to lower-pressure pipelines and transport to a selected injection site. Using expansion valves, however, has some shortcomings: (i) the fluid potential, in the form of kinetic energy and pressure which can produce mechanical work or electricity, is wasted, and (ii) due to the Joule-Thomson cooling effect, the reduction in the temperature of the released CO [...]

by Peng Li  , Chi-Yao Chang  and Amsini Sadiki

Received: 02 April 2021;  Published: 28 June 2021;  doi: 10.21926/jept.2102026

A numerical model describing the ballistic behavior of a commercially used initiator is presented in this article. This model was built on the principle of conservation of mass and energy in the multi-phase framework incorporated with multi-loaded conditions. After obtaining the information about the grain size distribution in each composite, a fixing factor was proposed based on the surface area ratio of the composites. Thus, the solid propellant burning process based on distributed grain size was described, and t [...]

by Wilson C. Chin  , Xiaoying Zhuang  and Jamie A. Chin

Received: 07 September 2024;  Published: 06 December 2024;  doi: 10.21926/jept.2404023

Our new approach to MWD mud pulse telemetry offers significant increases over conventional data rates. Using waveguide acoustics, we show that common drilling communications channels support carrier frequencies exceeding several hundred Hertz. Such signals are prone to attenuation over large drill pipe distances. Low power, self-spinning “turbosirens” are designed, providing high torque and rotation rate performance at all flow rates without electric or hydraulic motor drives. The sirens rotate, drawing only on the [...]

by Hong Yong Sohn  , Mohamed Elzohiery  and De-Qiu Fan

Received: 28 June 2021;  Published: 23 September 2021;  doi: 10.21926/jept.2103042

This article describes the development of a novel ironmaking technology based on flash reduction. The development started with the proof of the kinetic feasibility, considering that a typical flash reactor provides only a few seconds of residence time. This was followed by tests in a laboratory flash reactor and finally a pilot plant operation. The rate equations formulated in this work were developed considering the optimum combination of temperature, residence time, and reducing gas partial pressure to achieve &# [...]

by Khaliq Ahmed  , Periasamy Vijay  , Moses Tadé  , Amirpiran Amiri  , Zongping Shao  and Karl Föger

Received: 31 July 2020;  Published: 18 January 2021;  doi: 10.21926/jept.2101004

This report is an account of research and development activities undertaken by the Centre for Process Systems Computations, Department of Chemical Engineering at Curtin University, Western Australia in the area of solid oxide fuel cells. The focus of work of the group included 1)effect of cell macrostructure and microstructure on electrochemical performance with a view to optimise both macro- and micro-structure 2) electrochemistry modeling for simulating electrochemical performance 3) internal reforming aspects im [...]

by Pluvinage Guy  and Capelle Julien

Received: 03 March 2022;  Published: 01 September 2022;  doi: 10.21926/jept.2203029

Hydrogen is a dangerous gas due to its low ignition energy, wide flammability range, promotion of the embrittlement of steel, and its high coefficient of permeation for polymers. The fracture toughness and failure elongation of pipe steels are strongly impacted by hydrogen embrittlement, whereas yield stress and ultimate strength are moderately impacted. Specific tools are required for the pipe defect assessment used for the transport of hydrogen, which is pure or blended with natural gas. The safety factors associ [...]

by Oscar Daoura  , Maya Boutros  and Franck Launay

Received: 01 September 2020;  Published: 26 January 2021;  doi: 10.21926/jept.2101007

CO2 reforming of CH4, also referred to as the Dry Reforming of Methane (DRM), is considered an excellent method to produce H2 and CO (syngas), which are known to be used for the production of higher alkanes and oxygenates. Despite nickel’s moderate toxicity, Ni-based heterogeneous catalysts are considered excellent candidates for use in DRM due to their reasonable performances and economic advantages. However, these materials also present severe drawbacks, such as sintering of the active phase and coke (carbo [...]

by Aditya Sharma  , Opeyemi Bello  , Catalin Teodoriu  and Hamidreza Karami

Received: 15 February 2021;  Published: 30 June 2021;  doi: 10.21926/jept.2102030

The Industry 4.0 is here, and advanced technologies are widely available for domains such oil and gas which are traditionally slow in adopting extreme new technologies. This paper presents the design architecture and implementation of effective data acquisition (DAQ) and monitoring system applied to an experimental sucker rod pumping unit for both event occurrence and educational purpose using latest technological advancements and industry 4.0 principles. The designed framework allows control and monitoring of anal [...]